3538A LARGE GROUPING OF BULLET MOLDS, RELOADING TOOLS

CURRENT BID
600.00USDby B*********T (50399)
ENTER YOUR MAXIMUM ABSENTEE BID[?]
You must bid at least
650.00USD
USD
650.00 x 1 unit = 650.00USDApplicable fees & taxes are added at checkout.
[?]Live Online Auction Starts In 2026 Apr 19 @ 10:00 (UTC-04:00 : AST/EDT)
Category Firearms & Military
Auction Currency USD
Start Price 550.00 USD
Estimated at 1,100.00 - 1,400.00 USD
AND FIREARM RELATED ACCESSORIES. Reloading Tools: 1) Ideal No. 6 reloading tool in original green labeled box. Box markings include picture of No. 6 tool which was specifically made for Colt's Lightning, Winchester, Marlin and other magazine rifles and pistols. Marked "IDEAL MANUFACTURING CO. NEW HAVEN, CONN. U.S.A." on the box. Nickel plated tool with blued steel, double adjustable chamber. Chamber is marked "248". Tool is marked "38-55 M.". Integral flat point bullet mold. Original instructions and powder dipper included. Tool is worn with flaking finish. Box has wear, staining and loose corners, but labeling remains in generally legible condition. 2) Ideal No.4 reloading tool with integral bullet mold. Nickel-plated mold is marked "32-20" and has a solid chamber. Tool is in original plain box with yellow labeling. Box marked on the end, "ONE SET, IDEAL NO.4 / 32-20 / LIGHTNING RIFLE". Box has repaired corners and staining with legible labeling. Tool has wear and handling marks, but appears in serviceable condition. 3) Ideal No.4 nickel-plated reloading tool with integral bullet mold. Tool is complete with decapping pin and powder dipper. Housed in it's original factory box. Plain cardboard box with green labeling. Box is labeled on the end "ONE SET, IDEAL NO.4 / 38-40 / COLT'S / LIGHTNING RIFLE". Tool has light wear, but retains most of it's original nickel. Box has staining, wear and partial missing flap. Labeling remains legible. 4) Ideal No.6 reloading tool marked "50 EX" with integral hollow point bullet mold(hollow point insert is not present). Non-adjustable seating chamber. Mold has cleaned appearance returning to gray and patina, but appears to be in serviceable condition. 5) Ideal No.4 reloading tool marked "45 COLT'S". Additionally marked "IDEAL M'F'G CO". One line patent date. Replacement sprue-plate. Tool has notable wear and dents around the bullet mold. / COLT BULLET MOLDS: 1) Colt Model 1855 Rifle Mold. This mold, casting a round ball and a pointed conical bullet, was used with the Model 1855 revolving rifle. The high-quality mold with wooden handles is marked on the sprue-plate "COLTS / PATENT". Bull shows wear, dings and handling marks, notable on the right side of the mold and the end of the sprue-plate. 2) Two well-made gang molds, casting a 44 caliber pointed revolver bullet. One mold appears to cast heel-type bullets and one mold has a single-lubricating groove. These molds are very similar to the Colt gang molds pictured on page 103 of "Reloading Tools of the Black Powder Era 1850-1910 Vol. 2 by Rowe and Curtis". The mold casting the lubricated bullet has "254" on the left side and "254 S" on the right side near the hinge-pin. Molds have moderate wear, turning gray and patina with the normal small dents associated with vintage bullet molds. The sprue-plate screw on the unmarked mold has been filed bright on top. Molds appear to be in serviceable condition. 3) Colt Brass Revolver Mold. Casts one conical and one round ball approximately .290 diameter. Steel sprue-plate marked faintly "COLTS / PATENT". Mold is worn with numerous small dents. 4) Brass mold casting one pointed and one round ball approximately .310 diameter. Mold made without sprue-plate is marked on top "COLTS / PATENT". Well-worn mold with numerous handling marks. 5) Steel mold casting one conical and one round ball approximately .310 diameter. Sprue-plate marked with partially legible Colt's Patent. Mold is overall patina with wear and handling marks. 6) Two iron molds casting a pointed bullet and round ball, both molds marked "COLT'S PATENT" on the sprue-plates. 6) Two late-type dragoon molds casting a round ball and a grooved pointed bullet. 44 caliber. Marked on the sprue-plate "COLT'S / PATENT". Molds show heavy usage with turning gray and patina with numerous small dents. SHARPS MOLDS AND ACCESSORIES INCLUDE: 1) Steel mold. Mold is marked with "SHARPS RIFLE CO / BRIDGEPORT / CONN. / CAL. 44 / 297". Both handles have "27" assembly number. Nose pour bullet with two lubricating grooves. Interior surface of bottom plate is flat. Mold has been cleaned, returning to gray and patina, but appears to be in a worn but serviceable condition. 2) Steel Sharps Mold marked with partly legible "SHARPS RIFLE CO". Additional markings are "CALIBRE 1 1/8 / 405". "473" assembly number appears on both handles. Nose pour mold casts a cylindrical bullet for paper patching. Domed bottom plate. The dome allows for a slightly hollow based bullet. The hollow allows for the tail of a paper patch to be folded-over. Mold is well-worn with oxidation, light pitting and handling marks. 3) Sharps steel mold marked "SHARPS RIFLE CO / BRIDGEPORT / CONN. / CAL. 44 / EXP 277". Handle is additionally marked in script "Old Reliable". "5" assembly number. Base pour grooved bullet has provision for a nose pin(not present) which is the diameter of a .22 rimfire cartridge. This would allow the use of a .22 short cartridge inserted into the bullet to make an explosive bullet. Mold is worn, turning gray and patina with handling marks, but appears serviceable. 4) Steel mold marked on top of handle "NEW MODEL 1850?". "52". Mold is for the Sharps Percussion Rifle and has seen numerous use with heavy dents and handling marks. 5) Cartridge case and bullet swage with base. The body of the case swage is marked "40 SHARPE 285G". The bullet swage is unmarked. Base is marked "40". 6) Steel headspace gauge marked ".40-90 / SHARPS / STRAIGHT / NO 28". Gauge is in very good condition. / MAYNARD MOLDS: 1) Steel mold marked on the right side of the body "MAYNARD ARMS CO / WASHINGTON / MANUFACTURED BY / MASS. ARMS CO / CHICOPEE FALLS". Mold casts a single pointed bullet with one lubricating groove. Bullet measures approximately .520 at the base. Mold is turning gray and patina with spots of oxidation and pitting, but appears to remain serviceable. 2) Two cavity bullet mold. Mold is designed to cast two different bullet weights. Mold is solid and bullets are dropped out base-first. One cavity is marked .330 and the other is .285. Flat nosed bullets. Mold is marked on the end ".40 / MAYNARD / 1882". Heavy sprue-plate is secured by hex-head screw. The mold has a tapered boss at the rear which is threaded and accepts the shop-made replacement wooden handle. Mold has heat discoloration indicating use with light wear. ADDITIONAL BULLET MOLDS INCLUDE: 1) British Adams revolver mold. Two cavity brass mold casts a conical bullet and a round ball approximately .430 in diameter. The high quality mold is marked with a crown / "REGISTERED / R. ADAMS / 28 NOV 1851" in an oval and is additionally marked "56". Steel sprue-plate. Sprue-plate is marked "13". Mold has a pleasing moderately worn patina. Sprue-plate has oxidation and light pitting. 2) Brass mold hand-stamped at bottom "C.GR / RR" with steel sprue-plate. Mold casts two grooved 54 caliber pointed bullets. Mold is well-worn, turned patina with numerous dents and handling marks. 3) STARR single cavity brass revolver mold. Steel sprue-plate with thumb-lever. Hardwood handle. Unmarked mold casts a conical bullet. Mold has been lightly cleaned with wear and numerous handling marks. 4) Manhattan Arms steel two cavity revolver mold. 36 caliber. Casts a pointed bullet and round ball. Mold is marked on sprue-plate "MANHATTAN FIREARMS / MANFG CO NY". Mold is turning gray with wear and numerous dents. 5) Modern-Bond two cavity bullet mold blocks with handles. Mold blocks which cast semi-pointed bullets. Approximately 280 in diameter. Mold blocks are marked "B-280-780". 6) Large all-steel 9 cavity gang mold for an approximately .450 round ball. Mold is marked "2-15-44". Steel sprue-plate. Mold has moderate wear, but appears serviceable. 7) Steel gang mold for casting two sizes of bird shot measuring approximately .230 and .190 in diameter. Mold is unmarked. Mold is notably worn, heavily cleaned and loose in the hinge-pin. 8) Steel mold. Single cavity. Casting an approximately .520 round ball. Mold has nipper type sprue-cutter and is marked only with a "U.S." under handle. 9) Unmarked two cavity brass mold casting a round ball and pointed bullet. Round ball measures approximately .410. Bullets measures approximately .320. 10) Lyman Ideal .310 Tong Tool. 30-06. The large handles are steel and have a plumb coloration. Handles are marked "IDEAL / MIDDLEFIELD / CONN. / USA". The original orange box contains the handles plus the following threaded accessories. No. 311, 329, no.2 plus two unmarked sizing dies. Spare decapping pins. Instruction sheet and primer pocket cleaner. Orange box with black lettering. Tooling shows use, but remains serviceable. Box has worn, but legible labeling. 11) Modern-Bond brass(tong tool). Tool is marked "MODERN BOND CO. / WILMINGTON, DEL. / USA". Tool is equipped with a no.249 steel sizing die. Features a built-in chamfering tool and a priming station. Tool is turning a pleasing patina with light wear and spots of oxidation. 12) Pope style cartridge re-and-de capper. Constructed from blued steel and has a cartridge holder marked "45-70". Tool appears in good serviceable condition. 13) Early Remington hand shot shell loading tool converted to re-and-de prime 32-40 Win cartridges. Workmanship is of the hobbyist gunsmith type. 14) Group of four antique bullet mold cherries. Three are for pointed bullets, one is for blunt round nose. 15) Hollow point pin for bullet mold with wooden knob does not fit anything in the lot. 16) 16 Gauge shot shell rod seating tool with base. Brass tube is marked "BRIDGEPORT / G1 CO / 1149 / 16". 17) Shop-made breech seater and palm rest for unknown target rifle. Hobbyist gunsmith workmanship. 18) Small quantity of cast lead 32 caliber bullets. 19) Hinged brass combination tool with hammer-face, wrench and screwdriver. Marked "ECONOMY TOOL MANUFACTURING COMPANY". CONDITION: as stated. PROVENANCE: The Esteemed Norm Greenberg Collection. (02-24840-2/RW). NON-GUN. $1,100-1,400.